联系方式

  • QQ:99515681
  • 邮箱:99515681@qq.com
  • 工作时间:8:00-23:00
  • 微信:codinghelp

您当前位置:首页 >> OS作业OS作业

日期:2018-09-14 03:18


159.102 Computer Science Fundamentals Assignment 3

You have been asked to write a C program that simulates a 'Brookshear Machine'.

The program reads machine code from a text file "a3.txt".

Each line in the file contains 4 hexadecimal digits.

The first two digits on the first line make up an 8-bit byte that is to be stored at location 0 in the memory of the Brookshear

Machine. The second two digits make up an 8-bit byte that is to be stored at location 1 in memory.

The next line contains two bytes that are stored at locations 2 and 3.

This is repeated until you get to the end of file.

Each line will be valid , and the data will fit into 256 bytes.

The Brookshear Program that these instructions form may not be particularly interesting, but it will be valid.

Your program steps though the machine code, one instruction at a time. Before each instruction, your program prints out a line

of text that describes the current contents of the Program Counter, the instruction to be executed and the registers.

Each time an instruction is executed your program alters the Program Counter, Registers and Memory accordingly.

The format of the output line is:

PC INST – [R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF]

Where PC is the program counter, INST is the current instruction and R0 through to RF are the value of the sixteen registers.

Each field is output as a 2 or 4 digit hexadecimal value (use the X format specifier to get capital letters) with a leading 0 if

necessary.

Output continues (with no user intervention) until the Halt instruction is executed, at which time your program also stops.

A Halt instruction will occur in all test programs.

Example: if a3.txt contains:

B404

239A

2412

5345

350C

C000

Then the output is:

00 B404 – [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00]

04 2412 - [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00]

06 5345 - [00 00 00 00 12 00 00 00 00 00 00 00 00 00 00 00]

08 350C - [00 00 00 00 12 12 00 00 00 00 00 00 00 00 00 00]

0A C000 - [00 00 00 00 12 12 00 00 00 00 00 00 00 00 00 00]

Use unsigned char's for your PC, registers and memory.

When reading the a3.txt file, be careful with alignment problems in the scanf-like functions. First read each line into an

unsigned int variable, then extract out the two bytes using bit-wise operators and store them in your memory array.

Your program must open the file a3.txt for reading by using the following arguments to the fopen function call

f = fopen("a3.txt","r"); //you may change 'f' if you prefer!

Make sure that your program compiles and links using gcc. Submit your assign3.c electronically.

Marks will be awarded on how many test programs your program handles correctly.

There should be no other output apart from that stated above.

Test your program with different machine instructions before submission.

Due date: 5.00pm Mon 17

th September, worth 4%.

Brookshear machine instructions

1RXY Load register R with the value at memory address XY

2RXY Load register R with the value XY

3RXY Store the value in register R at memory address XY

40RS Copy/move the value in register R to register S

5RST Add the values in registers R and S and put the answer in register T

7RST Bit-wise OR the values in registers R and S and put the answer in

register T

8RST Bit-wise AND the values in registers R and S and put the answer in

register T

9RST Bit-wise XOR the values in registers R and S and put the answer in

register T

AR0X Rotate the contents of register R X times to the right

BRXY Jump to the instruction located at memory address XY if the value in

register R is equal to the value in register 0 (i.e. change the PC to XY)

C000 Halt


版权所有:留学生编程辅导网 2020 All Rights Reserved 联系方式:QQ:99515681 微信:codinghelp 电子信箱:99515681@qq.com
免责声明:本站部分内容从网络整理而来,只供参考!如有版权问题可联系本站删除。 站长地图

python代写
微信客服:codinghelp